Door Lock Backset Measurement

Sometimes it s easier to measure from the edge of the door to the highest point on the bore hole. Other backsets include 2 used by national and lori lock and 5 used by weiser weslock kwikset and others. This is very important when replacing locks because you don t want to have to drill new holes if you can help it.

decorative security screen doors brisbane design of sheet metal brackets door handle with lock and key homebase decorative palm leaf ceiling fan blades decorative wall shelves for living room diamond gutter shield door lock actuator carid dji osmo action accessories india

Faqs Keyless Door Locks Keyless Front Door Locks Commercial Keyless Door Locks Electro Keyless Entry Locks Keyless Door Lock Entry Door Locks

How To Measure Backset Measure From The Edge Of Door To The Center Of The Bore Hole Or The Lock Body That You A Door Locks And Latches Door Locks Door

Determine The Backset Of Your Door Shop Doors Door Installation Residential Doors

Standard Tubular Conversion Latch 2 3 X2f 8 Quot Backset House Of Antique Hardware Mortise Lock Door Locks And Latches Hardware

Yale Front Door Lock Narrow Body High Security Nightlatch 40mm Backset Polished Chrome Front Door Locks Front Door Handles British Standards

Image Result For Door Latch Mechanism Door Handles Door Latch Lock

5 backsets are only available for some schlage locks and some kwikset locks.

Door lock backset measurement.

Check the other dimensions too most of our pages show plate and lock case dimensions. Dead bolt latches top 2 3 4 bottom 2 3 8 note. The backset is the distance from the edge of the door to the center of the 2 1 8 inch bore hole. The backset measurement is the distance from the centre of the keyhole to the leading edge of the lock.

The most common sizes here are 44mm on a 64mm 2 5 lock case and 56mm on a 76mm 3 lock case. Two standard backsets are 2 3 8 and 2 3 4. The most common backset is 2 3 8 but 2 3 4 is also quite common usually used on exterior doors. In the uk and much of europe these dimensions can vary from 25 to 60 mm and many medallion knobs are placed in the center of the door creating a very large backset.

These smaller backset sizes are generally european and some are still in use today. Falcon used to make a 5 backset that would work with emtek hardware but i believe it is no longer available. To do this measure the backset distance of your old lock. Backsetthe distance from the edge of the door to the center of the lock bore.

C the case height. Most commercial doors have a backset of 2 3 4 inches 69 8 mm while residential doors measure 2 3 8 inches 60 3 mm. If you dont have any hardware on your door just measure from the edge of the door to the center of the bore hole the large hole where the door knob assembly is mounted. The backset is measured by placing a tape measure or ruler from the center of the keyhole to the forend of the mortice lock.

Mortised latches come in a radius corner rounded on the edges or a squared corner configuration. These equate to case sizes of 2 1 2 or 3 in imperial measurements. Please see the demonstration below. Pack your locks with a 2 3 8 inch or 2 3 4 inch latch depending on which backset you specify.

Standard backsets are either a 2 3 8 backset or 2 3 4 backset. Some older residences will have variations to installed locks. 2 3 8 inches and 2 3 4 inches. There is a range of backset long body locks at 20mm 25mm 30mm 35mm 40mm 50mm and 70mm.

In the united states there are two common backsets for residential door locks. Almost all domestic mortice locks and tubular latches are supplied with either a 44mm or 57mm backset length.

Pin On Antique Hardware

Door Hardware Glossary Of Terms Homestead Hardware Best Front Doors Door Hardware Home Protection

Standard Mortise Lock With Strike Plate And Keys 2 1 4 Backset In Bright Brass Mortise Lock Antique Hardware Mortising

Small Solid Brass Mortise Latch 1 3 8 Backset In Polished Brass Polished Brass Mortise Lock Solid Brass

Source : pinterest.com